Touch Screen Automotive Interior Combustion Tester

Number:

DH-QCS-2

Activity price:

Market price:

Category:

Touch Screen Controlled Split Automobile Interior Combustion Tester

Message

Details

Touch Screen Automotive Interior Combustion Tester

Application

Designed according to the requirements of the national standard GB8410-2006 "Combustion Characteristics of Automobile Interior Materials", it also complies with the simulated combustion performance safety test items specified in the US Automobile Safety Technical Regulations FMVSS 571.302 and other standards, the German standard DIN7520 "Combustion Characteristics of Automobile Interior Materials" and TL1010 "Combustion Characteristics of Automobile Interior Materials". It is used to identify the horizontal combustion characteristics of interior materials of cars, multi-purpose passenger cars, trucks and buses.

The instrument has a reasonable structural design, convenient operation and maintenance, and the ignition system adopts high-voltage electronic ignition, which is safe and labor-saving.

Should be noted that: GB8410-2006 "Combustion Characteristics of Automobile Interior Materials" 4.2.9 requires that the combustion box should be placed in a fume hood, the internal volume of the fume hood is 20-110 times the volume of the combustion box, and any dimension of the length, width and height of the fume hood shall not exceed 2.5 times of any of the other two dimensions. The vertical speed of the air flowing through the fume hood at the side beam 100mm before and after the final position of the combustion box should be between 0.10m/s-0.30m/s. The equipment has not been designed for these two regulations. If you have requirements for these two regulations, please choose the -3 model automobile interior material combustion test device.

In addition, the QCS-2 automobile interior material combustion test device adopts a split design. If the user considers implementing the requirements of the fume hood and wind speed in GB8410-2006 in the future, the fume hood can be customized and added by the user, and the equipment can still be used.

Technology Parameters

Temperature: -5℃-30℃.
Relative humidity: ≤ 85%.
Power supply: 220V+10%, 50HZ, power: 100W.
Gas source: liquefied petroleum gas
Seven-inch full-color touch/display screen:

Size: 7 inches, effective display size, length 15.5cm, width 8.6cm;
Resolution: 800*480
Communication interface RS232, 3.3V CMOS or TTL, serial port mode.
Storage capacity: 1G
Adopt pure hardware FPGA to drive the display, "zero" startup time, power on that can run.
Adopt M3+FPGA architecture, M3 is responsible for command parsing, FPGA focuses on TFT display,
The main controller uses a low-energy processor and automatically enters energy-saving mode.

The experimental data can be stored in the touch screen, and historical data can be retrieved
After recording the burning time, the equipment automatically calculates the test result combustion speed (also known as the burning rate)
Dimensions: Control part size: 590mm*210mm*460mm, combustion part length 383 width 205 height 355 (inside the box) (stainless steel material)
The accuracy of the stopwatch is not less than 0.5s.
The Bunsen burner (i.e., burner) applies flame to the sample for 15s.
The inner diameter of the Bunsen burner tube is 9.5mm+ 0.1mm, and the length is about 100mm.
Test inclination: The Bunsen burner burns vertically at 90° to the horizontally placed sample
Flame height: adjustable from 20mm± 2mm to 100mm±2mm (generally adjusted to 38mm)
Flame application time: adjustable from 0-999.9s±0.1s (generally selected as 15s)
Continued burning time: 0-999.9s±0.1s, observe that the flame reaches the first mark and then start and pause manually
Combustion gas: liquefied petroleum gas or coal gas Note: The gas source and connection connector are provided by the user

Installation Conditions (User-prepared)

Space	Dimensions	Control part size :590mm210mm460mm
		Combustion part size:383205355(mm)
	Weight（KG）	about 30 kg
	Test bench	A workbench with a length of not less than 1 meter and a width of not less than 0.75 meters. The exhaust pipe needs to be connected (diameter 10cm)
Power supply	Voltage	220V±10％,50HZ
	Power	150W
Water		/
Gas		uses coal gas or liquefied petroleum gas
Pollutants		Smoke and dust
Ventilation		The smoke exhaust pipe at one end of the equipment needs to be connected to the smoke treatment and purification system
other requirement		Gas cylinder with pressure reducing valve (can adjust to 0.3 MPa)

Keyword:

None